A2 just good to go...
Moderators: rickf, raymond, Mr. Recovery
A2 just good to go...
Hi all.
It's probably my second post here. I'm Martin. I'm Polish.
I would like to thank everyone who helped me rebuild my M151 A2.
Especially Richard for technical support.
In accordance with the interests and work done on SOF Mutt.
Here 'a few photo, more can be found in the section on HQ5.pl completed projects. http://hq5.pl/en/projekty or http://www.facebook.com/pages/HQ5/274599375922063
Here are some Mutts. About 30 different types. http://farm9.staticflickr.com/8423/7575 ... d6cb_z.jpg
I must admit that I would need a few more parts ...
Yours.
UES.
It's probably my second post here. I'm Martin. I'm Polish.
I would like to thank everyone who helped me rebuild my M151 A2.
Especially Richard for technical support.
In accordance with the interests and work done on SOF Mutt.
Here 'a few photo, more can be found in the section on HQ5.pl completed projects. http://hq5.pl/en/projekty or http://www.facebook.com/pages/HQ5/274599375922063
Here are some Mutts. About 30 different types. http://farm9.staticflickr.com/8423/7575 ... d6cb_z.jpg
I must admit that I would need a few more parts ...
Yours.
UES.
-
- 2nd Lieutenant
- Posts: 877
- Joined: June 22nd, 2009, 2:29 pm
- Location: Taylorsville, UT
- Contact:
Re: A2 just good to go...
Nice restore and great seeing the right colors and camo pattern.
1968 M151A1
1967 M416
1967 M416
Re: A2 just good to go...
Nice work.
Sent from my Nook Tablet using Tapatalk 2
Sent from my Nook Tablet using Tapatalk 2
"People sleep peaceably in their beds at night only because rough men stand ready to do violence on their behalf."
George Orwell
-------------------------------------
"I once was one of those men."
salt6
http://www.mg42.us
George Orwell
-------------------------------------
"I once was one of those men."
salt6
http://www.mg42.us
- Jay Mallari
- 1st Lieutenant
- Posts: 931
- Joined: December 7th, 2007, 10:30 pm
- Location: Middlesex, England
Re: A2 just good to go...
Very nice restoration Martin and welcome to the board. Has the owner of this mutt contemplated of cutting the excess fording intake pipe to clear the 50 cal barrel when it swings?
Had to cut mine for clearance.
Had to cut mine for clearance.
Re: A2 just good to go...
This is my MUTT;)
I'm finishing work.
I put new springs and boasts distances. Mutt went up nearly 2 inches. Because I had a problem with the tires rubbing the fenders.
Yes. I cut a set of fording intake / exhaust about 10 cm.
Looking for cable and antenna base to your RTO.
I have a problem because the RTO can not set the base frequency antenna.
I do not know which cables to the base and I have gotten to your RTO.
Can you tell which type of cable is appropriate?
I know that large RT 524 runs. Made contact with ANPRC152.
Small R442 is not broadcasting. Boys of communication with me said that it chokes. What does this mean any??
I'm finishing work.
I put new springs and boasts distances. Mutt went up nearly 2 inches. Because I had a problem with the tires rubbing the fenders.
Yes. I cut a set of fording intake / exhaust about 10 cm.
Looking for cable and antenna base to your RTO.
I have a problem because the RTO can not set the base frequency antenna.
I do not know which cables to the base and I have gotten to your RTO.
Can you tell which type of cable is appropriate?
I know that large RT 524 runs. Made contact with ANPRC152.
Small R442 is not broadcasting. Boys of communication with me said that it chokes. What does this mean any??
Re: A2 just good to go...
2 x M151A2. Bielsko Biala. Poland. Military Vehicle Rally "Operation South"
http://www.youtube.com/watch?v=d8Ht0p84 ... ure=relmfu
http://www.youtube.com/watch?v=d8Ht0p84 ... ure=relmfu
Re: A2 just good to go...
Welcome aboard and Great Job on the MUTT. Looks like you have a lot of fun with it.