What you need for a mutt radio install
Moderators: rickf, raymond, Mr. Recovery
Re: What you need for a mutt radio install
Yes you guys are correct, I am like a kid with a new toy and cannot wait, I have contacted a few of the people that you have listed but have not found one yet, but I will slow down and hopefully find one in the near future, I am trying to get everything installed and dry fitted for paint in the very near future.
Thanks for all the information and if one comes available please let me know.
Thanks for all the information and if one comes available please let me know.
Re: What you need for a mutt radio install
I might have one,I am not going to use it, so let me look
mark
mark
mark
1968 m274A5
1960 m151
1981 m151A2
1964 m416
1971 m416
1968 m274A5
1960 m151
1981 m151A2
1964 m416
1971 m416
Re: What you need for a mutt radio install
Hi,
Do I need the INERCONNECTING BOX, J-3513A/U to connect my RT-524 and R-442?
Thanks!
Do I need the INERCONNECTING BOX, J-3513A/U to connect my RT-524 and R-442?
Thanks!
moose53 wrote:Since the question seems to come up from time to time here is what you need for a mutt radio install...
This is a basic installation, not including voice scrambling or direction finding gear, or remote point operation.
1. Transceiver.
either a RT-524 (most common), an RT-246, or a PRC-25 or 77 portable w/amp unit.
2. Optional Aux. Receiver -
R-442
3. Mounting tray for each radio -
MT-1029/VRC for the transceiver and MT-1898/VRC for the Aux Receiver.
4. Sponson Plate -
Reinforces fender to take the weight of the radio
SC-DL-48676 for the MT-1029 mount
SC-DL-48682 for the MT-1898 mount
5. Antenna
either AS-1729/VRC or AT-912/VRC for the Tranceivers and AB-15/GR or AB-558/GR for the Aux Receiver.
The AS-1729/VRC Antenna consists of the MX-6707 base, AS-1730 lower whip section and the AT-1095 Upper whip section, a tip ball, and tiedown. It mounts on the 3 piece corner antenna mount (sugar scoop).
The AT-912/VRC antenna was an early version with a large rectangular matching unit. It consisted of MX-2799 matching unit, AS-719 Antenna Base, AT-1096 Lower whip section, AT-1095 upper whip section, Tip Ball, and Tiedown.
The AB-15/GR Antenna consisted of a AB-15 base (2 piece ball insulator), MS-116A, MS-117A, and MS-118A whip sections, UG-273 cable adapter, SC-DL-48528 side mount bracket, and SC-C-446109 brush guard. the AB-558/GR was for mounting on the sugar scoop bracket like the as-1729, and used the same whip sections as the AB-15.
6. Accessories
LS-454/U speaker -necessary for RT-246 and R-442, optional on RT-524
M-80/U Hand Microphone
H-189/GR or H-250/GR Handset (looks like telephone handset)
H-161/U Headset with microphone
H-140/U or H-251/U Headset w/o mic
C-2299/VRC Control box, power, audio, allows control of transceiver from dash.
C-2742/VRC - Control Box, channel selection for RT-246 only.
7. Cables
CX-4720 - Vehicle Batteries to MT-1029 Mount
CX-4721 - MT-1029 Mount to MT-1898 mount and/or MT-1898 Mount to MT-1898 Mount depending on installation
CX-4722 - Control cable from Transceiver to antenna matching unit.
CX-4723 - Control Box C-2299/VRC to Transceiver
CX-7059 - Control Box C-2742 to MT-1029 mount.
CG-1773 - Coax cable from transceiver or Aux receiver to antenna (all)
These are the parts needed for a basic radio installation There are additional items for secure comms and remote comms that I omitted since not too many people want to go that far.
Jim
When you go to war, you go to war all the way. You don't go to war piecemeal.
You go, and you go to win.
(General H. Norman Schwarzkopf)
You go, and you go to win.
(General H. Norman Schwarzkopf)
- richard
- Command Sergeant Major
- Posts: 621
- Joined: August 10th, 2011, 5:52 am
- Location: Lower Saxony, Germany
- Contact:
Re: What you need for a mutt radio install
The TM 11-5820-401-10-1 says: Whenever a regular R-T mount (MT-1029/VRC) is modified to include interconnecting box J-3513/U it becomes a Vinson R-T mount.
Only Vinson Comsec equipment can be used in the radio system.
From my understanding, you can use the RT-524 and R-442 w/o the box as Jim (aka moose53) described it in detail above.
Only Vinson Comsec equipment can be used in the radio system.
From my understanding, you can use the RT-524 and R-442 w/o the box as Jim (aka moose53) described it in detail above.
European Distributor for CMD Body Panels: http://www.M151BodyPanels.eu
1978 M151-A2
1978 M416-A1
1972 M561
1964 M35-A2 w/winch & shelter
1978 M151-A2
1978 M416-A1
1972 M561
1964 M35-A2 w/winch & shelter
Re: What you need for a mutt radio install
Great!
Thanks,
Pascal
Thanks,
Pascal
When you go to war, you go to war all the way. You don't go to war piecemeal.
You go, and you go to win.
(General H. Norman Schwarzkopf)
You go, and you go to win.
(General H. Norman Schwarzkopf)
Re: What you need for a mutt radio install
Richard is correct, the interface box J-3513/u was used to connect the TSEC/KY-57 Speech Scrambler to the RT-524 or RT-246. The only connection between the RT-524 and R-442 was a power cable between the radio mounts.
Jim
Jim
Zigzag50, Northeast51, KC2QDZ
MVPA # 30032 G838.org
--------------------------------------
1971 G838-M151A2 1966 G857-M416
1968 G748-M101A1 1976 G748-M116A1
1990 MEP-701A
--------------------------------------
Real jeeps have horizontal grille slots
MVPA # 30032 G838.org
--------------------------------------
1971 G838-M151A2 1966 G857-M416
1968 G748-M101A1 1976 G748-M116A1
1990 MEP-701A
--------------------------------------
Real jeeps have horizontal grille slots
- richard
- Command Sergeant Major
- Posts: 621
- Joined: August 10th, 2011, 5:52 am
- Location: Lower Saxony, Germany
- Contact:
Re: What you need for a mutt radio install
Hello Pascal,
Here comes an additional diagram from the TM. Hope it helps. Do you have all the cables, correct antennas, mounts and sponsons as listed by Jim?
Here comes an additional diagram from the TM. Hope it helps. Do you have all the cables, correct antennas, mounts and sponsons as listed by Jim?
European Distributor for CMD Body Panels: http://www.M151BodyPanels.eu
1978 M151-A2
1978 M416-A1
1972 M561
1964 M35-A2 w/winch & shelter
1978 M151-A2
1978 M416-A1
1972 M561
1964 M35-A2 w/winch & shelter
Re: What you need for a mutt radio install
Thanks Richard, this is great!
I have the radios, antennas, mounts, power cable, but not the antenna cables and connecting cables needed between the two stations...
Do you have access to those?
I have the radios, antennas, mounts, power cable, but not the antenna cables and connecting cables needed between the two stations...
Do you have access to those?
When you go to war, you go to war all the way. You don't go to war piecemeal.
You go, and you go to win.
(General H. Norman Schwarzkopf)
You go, and you go to win.
(General H. Norman Schwarzkopf)
- richard
- Command Sergeant Major
- Posts: 621
- Joined: August 10th, 2011, 5:52 am
- Location: Lower Saxony, Germany
- Contact:
Re: What you need for a mutt radio install
Hello Pascal,
Perhaps you should contact Michael Danziger in Germany. Here is a direct link to his Web shop's radio cable section. If you need any translation, because it is in German, please let me know.
http://www.reforger.de/de/60-us-funkgerate-kabel
Perhaps you should contact Michael Danziger in Germany. Here is a direct link to his Web shop's radio cable section. If you need any translation, because it is in German, please let me know.
http://www.reforger.de/de/60-us-funkgerate-kabel
European Distributor for CMD Body Panels: http://www.M151BodyPanels.eu
1978 M151-A2
1978 M416-A1
1972 M561
1964 M35-A2 w/winch & shelter
1978 M151-A2
1978 M416-A1
1972 M561
1964 M35-A2 w/winch & shelter
-
- Corporal
- Posts: 34
- Joined: November 14th, 2014, 11:02 am
Re: What you need for a mutt radio install
Here's my radio set up- RT 524 and R442. They are on loan from my neighbor who has a M151A2 (Yes, there are TWO MUTTs in my tiny neighborhood). All wiring and mounts were in my M151 when I bought it. I just took the whips out of the canvas bag, installed them, and plugged in the radios and everything worked great!
[URL=http://s819.photobucket.com/user/d ... .jpg[/img][/url]
[URL=http://s819.photobucket.com/user/d ... .jpg[/img][/url]
1964 Kaiser M151
1966 Stevens M416
1967 Stevens M416
1966 Stevens M416
1967 Stevens M416
Re: What you need for a mutt radio install
Except you have the wrong antenna for the 442. That should have an AB-15 mount and the three section whip. The whip sections are the M0116, M-117, M-118. The AB-15 mount si mounted on the passenger side right behind the door opening or on the old style AB-15 mount such as mine it is on the drivers side rear corner but it is only as high as the body side.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Corporal
- Posts: 34
- Joined: November 14th, 2014, 11:02 am
Re: What you need for a mutt radio install
I'm still shopping for the correct whip sections. They are always around $200.
1964 Kaiser M151
1966 Stevens M416
1967 Stevens M416
1966 Stevens M416
1967 Stevens M416
Re: What you need for a mutt radio install
Read the manual. What you can use also depends on what time frame you want to replicate.
"People sleep peaceably in their beds at night only because rough men stand ready to do violence on their behalf."
George Orwell
-------------------------------------
"I once was one of those men."
salt6
http://www.mg42.us
George Orwell
-------------------------------------
"I once was one of those men."
salt6
http://www.mg42.us
-
- Sergeant
- Posts: 72
- Joined: October 10th, 2014, 9:10 pm
- Location: southern California
Re: What you need for a mutt radio install
Can someone please post or send to me dimensions for the corner-mount extension? It looks simple and shouldn't be hard to replicate.
Thanks
-Ken
Thanks
-Ken
Keep 'em rolling!
Re: What you need for a mutt radio install
Just the extension that is added to the main mount?
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone