M416 Tarp Support

need more space? add a M416 trailer! and discuss it here.

Moderators: rickf, raymond, Mr. Recovery

Post Reply
User avatar
glcaines
Sergeant First Class
Sergeant First Class
Posts: 220
Joined: January 13th, 2023, 8:03 pm
Location: Hiawassee, Georgia

M416 Tarp Support

Unread post by glcaines » March 31st, 2024, 7:54 pm

Based on the instructions found in PM I built a tarp support for my M416 trailer. I modified the PM design by rounding the angular cut on each end of the board to minimize damage to the tarp from rubbing. It took me about 20 minutes to cut the wood, and works well. I coated the board with semigloss urethane and then put on two coats of Forest Green. The support fits snugly when in place.
Cargo Tarp Support B.jpg
You do not have the required permissions to view the files attached to this post.
M151A2 (1977), M151A2 (1973)
M416 Trailer
M35A3 W/W and M66 Gun Ring
M149A1 Water Buffalo Trailer
M105A1 Trailer
XM1061E1 Trailer
FLU419
M116A1 Trailer W/MEP003A Generator
M1030M1 USMC Diesel Motorcycle
M274A5 Mechanical Mule (4-Wheel Steer)

User avatar
glcaines
Sergeant First Class
Sergeant First Class
Posts: 220
Joined: January 13th, 2023, 8:03 pm
Location: Hiawassee, Georgia

Re: M416 Tarp Support

Unread post by glcaines » November 13th, 2024, 7:41 pm

Well, my tarp support didn't work out as well as I thought it would for my M416 trailer. I went back to the drawing board and created a new design which actually works quite well. I purchased two sheets of 1/2-inch exterior grade plywood. One sheet wasn't large enough to cover the width of the trailer bed, so I joined the two pieces lengthwise with 10-inch wide strips of 1/2-inch plywood on both sides. I used exterior-grade wood glue and my staple gun to keep it together and then added 5/16-inch stainless steel bolts. I cut small blocks of 1/2-inch plywood and attached them on the underside of the cover so that when the cover is in place on the trailer bed, the blocks are on the inside of the bed sides to keep the cover in place. The cover was cut to be an exact fit front and rear and sides where the edges of the cover sit on top of the bed, but don't protrude past the edges. I also rounded the corners of the cover. I then sprayed the entire cover top and bottom
Wood Cover Underside.jpg
with Forest Green paint. No more sagging tarps from rainwater or snow. One note, I don't pull the trailer with the cover on it without strapping it down. While driving, the air flowing across the top of the cover causes the air pressure to drop on top, which can cause the cover to lift up and fly off the trailer.
Wood Cover Installed.jpg
You do not have the required permissions to view the files attached to this post.
M151A2 (1977), M151A2 (1973)
M416 Trailer
M35A3 W/W and M66 Gun Ring
M149A1 Water Buffalo Trailer
M105A1 Trailer
XM1061E1 Trailer
FLU419
M116A1 Trailer W/MEP003A Generator
M1030M1 USMC Diesel Motorcycle
M274A5 Mechanical Mule (4-Wheel Steer)

User avatar
rickf
General
General
Posts: 20156
Joined: November 26th, 2007, 1:28 pm
Location: Pemberton, NJ.

Re: M416 Tarp Support

Unread post by rickf » November 13th, 2024, 10:35 pm

The one I always saw the most was bent pieces of PVC pipe. Just poked into the inside where the body protrudes in and bowed up across.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone

User avatar
LACRAC
Corporal
Corporal
Posts: 26
Joined: September 25th, 2023, 2:38 pm
Location: Tillson, NY

Re: M416 Tarp Support

Unread post by LACRAC » November 14th, 2024, 4:30 pm

this is what we used to do
dog house.jpg
You do not have the required permissions to view the files attached to this post.
1967 M151A1 - On the rotisserie

User avatar
LACRAC
Corporal
Corporal
Posts: 26
Joined: September 25th, 2023, 2:38 pm
Location: Tillson, NY

Re: M416 Tarp Support

Unread post by LACRAC » November 14th, 2024, 4:32 pm

this is what we used to do
dog house.jpg
1967 M151A1 - On the rotisserie

Post Reply