Fuel tank drain plug needed
Moderators: rickf, raymond, Mr. Recovery
-
- Corporal
- Posts: 43
- Joined: August 10th, 2015, 10:31 am
Fuel tank drain plug needed
Hi guys,
My '77 A2 restoration continues. Checking the underside in preparation for a media blast of the whole body I found fuel was weeping from the fuel tank drain plug area.
Removing the tank from the body meant a fuel and a vapour line having to be cut because of seized fittings. (Side Query: Has anyone re-flared a shortened line and reconnected it despite now missing the length of the lost nut?)
A fuel tank specialist has repaired the rusting around the drain plug flange and another small rust hole and reckons the general condition of the tank is good but on the bench I found the drain plug (Plug Pipe Duel Tank Drain p/no 444577) was well and truly seized. It has now been removed and in the process was well and truly destroyed.
I have searched all my usual sources but cannot locate this item. Does anyone have one(or two) they can sell please OR can it be replaced with a suitable bolt (perhaps a brass hex screw?) and a gasket?
Thanks, and stay safe all,
Challenger2
In the United Kingdom
My '77 A2 restoration continues. Checking the underside in preparation for a media blast of the whole body I found fuel was weeping from the fuel tank drain plug area.
Removing the tank from the body meant a fuel and a vapour line having to be cut because of seized fittings. (Side Query: Has anyone re-flared a shortened line and reconnected it despite now missing the length of the lost nut?)
A fuel tank specialist has repaired the rusting around the drain plug flange and another small rust hole and reckons the general condition of the tank is good but on the bench I found the drain plug (Plug Pipe Duel Tank Drain p/no 444577) was well and truly seized. It has now been removed and in the process was well and truly destroyed.
I have searched all my usual sources but cannot locate this item. Does anyone have one(or two) they can sell please OR can it be replaced with a suitable bolt (perhaps a brass hex screw?) and a gasket?
Thanks, and stay safe all,
Challenger2
In the United Kingdom
Re: Fuel tank drain plug needed
Just to clarify, are you talking about the bung?...or the plug itself?
If it's just the plug, that should be a standard, off-the-shelf, hardware store item here in the states.
If it's just the plug, that should be a standard, off-the-shelf, hardware store item here in the states.
You do not have the required permissions to view the files attached to this post.
-
- Corporal
- Posts: 43
- Joined: August 10th, 2015, 10:31 am
Re: Fuel tank drain plug needed
Hi M3A1,
Thanks for responding, yes it is just the plug. The original plug (or at least the one which came out) is a steel machined part with a threaded section (3/8" UNF?) and a square nut (now well rounded and with a good portion of the thread destroyed NOT by myself). I aim to keep things original where I can, and recover and restore as much as I can.
But this is ONLY a plug to keep the fuel in and be removed to drain when necessary? Would any similar piece be okay?
Challenger2
Thanks for responding, yes it is just the plug. The original plug (or at least the one which came out) is a steel machined part with a threaded section (3/8" UNF?) and a square nut (now well rounded and with a good portion of the thread destroyed NOT by myself). I aim to keep things original where I can, and recover and restore as much as I can.
But this is ONLY a plug to keep the fuel in and be removed to drain when necessary? Would any similar piece be okay?
Challenger2
Re: Fuel tank drain plug needed
That should be standard pipe thread. I don't know if metric is different or not. Probably.
Here is a link to Mcmaster Carr but if you have to buy one little item and have it shipped it will not be worth it. If you go with brass use teflon tape and do not tighten it too tight and definitely do NOT use stainless steel since the threads will gall and you will never get it out. I am surprised you got that on out.
https://www.mcmaster.com/npt-plugs/driv ... al-square/
Here is a link to Mcmaster Carr but if you have to buy one little item and have it shipped it will not be worth it. If you go with brass use teflon tape and do not tighten it too tight and definitely do NOT use stainless steel since the threads will gall and you will never get it out. I am surprised you got that on out.
https://www.mcmaster.com/npt-plugs/driv ... al-square/
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
Re: Fuel tank drain plug needed
I'll see if I can confirm that thread for you today. Have a lot going on at the moment.
- Mr. Recovery
- Brigadier General
- Posts: 2895
- Joined: December 5th, 2007, 9:03 pm
- Location: New Port Richey, Fl.
- Contact:
Re: Fuel tank drain plug needed
This is the only plug I have ever seen in the gas tank unless Bubba has changed it. looks like 3/8 NPT with a square head.
It looks to be the same plug that's used in the Intake
It looks to be the same plug that's used in the Intake
You do not have the required permissions to view the files attached to this post.
1960 M151 Run 1
1963 M151 Willys DoD 10-63 in Baltimore
1989 Alley Cat. "work in Progress"
NRA Life Member
American Legion Post 275 Fl
US Army 6 years 2nd Armored Cavalry Bindlach Germany
Colorado Army Nat. Guard 5 years
Md Air Guard 15 years active duty on C-130's
1963 M151 Willys DoD 10-63 in Baltimore
1989 Alley Cat. "work in Progress"
NRA Life Member
American Legion Post 275 Fl
US Army 6 years 2nd Armored Cavalry Bindlach Germany
Colorado Army Nat. Guard 5 years
Md Air Guard 15 years active duty on C-130's
-
- Corporal
- Posts: 43
- Joined: August 10th, 2015, 10:31 am
Re: Fuel tank drain plug needed
Thanks Rick,
NPT plugs are available here in the UK. I will probably go the brass route and as you suggest use Teflon tape and don't over tighten. I will also probably go Allen key fitting.
Challenger 2
NPT plugs are available here in the UK. I will probably go the brass route and as you suggest use Teflon tape and don't over tighten. I will also probably go Allen key fitting.
Challenger 2
Re: Fuel tank drain plug needed
I say don't go too tight because if it leaks a little you can always tighten it a little at a time until it stops and then you are there. That way you did not crank it way to tight just to make sure and have trouble getting it out the next time. Another thing you could use instead of the tape is Permatex #3 sealant. It never gets hard so the same thing applies. I use that on all of my thin gaskets and also on my coolant hoses. It prevents the corrosion of the aluminum housings on the pump and thermostat housings a bit and it also prevents the hoses from welding themselves to the housings. Easy to get on and easier to get off.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
- svramselaar
- Major
- Posts: 1109
- Joined: December 30th, 2007, 6:48 am
- Location: holland
Re: Fuel tank drain plug needed
hi
it is not a tapered plug parts number ms 20913-2s
a plug with a copper ring
https://www.wbparts.com/rfq/4730-00-221-2136.html
george
it is not a tapered plug parts number ms 20913-2s
a plug with a copper ring
https://www.wbparts.com/rfq/4730-00-221-2136.html
george
Re: Fuel tank drain plug needed
George, It IS a tapered pipe thread BUT, in looking at that designation I see it says it is an ANPT plug which is Aeronautical national pipe taper.
You can use a NPT plug with sealer and it will be fine, the military always wants things made to the finest detail for some reason. I can see it for aeronautical use but not in a dirty vehicle!
https://willrich.com/wp-content/uploads ... -Gages.pdf
You can use a NPT plug with sealer and it will be fine, the military always wants things made to the finest detail for some reason. I can see it for aeronautical use but not in a dirty vehicle!
https://willrich.com/wp-content/uploads ... -Gages.pdf
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
Re: Fuel tank drain plug needed
Hello George and Rick.....
Part Number MS20913-2S does not relate to NIIN 4730-00-221-2136.
What it DOES relate to is NIIN 4730-00-221-2137
And using Part Target, here's the result showing a correct cross-reference
see https://www.parttarget.com/4730-00-221- ... 0-221-2137
Ken
Part Number MS20913-2S does not relate to NIIN 4730-00-221-2136.
What it DOES relate to is NIIN 4730-00-221-2137
And using Part Target, here's the result showing a correct cross-reference
see https://www.parttarget.com/4730-00-221- ... 0-221-2137
Ken
Kind regards....
Ken
Always wanted - Details and pictures of M416 Trailer data plates & M151 data plates & body-tags for my research. Thanks!
Contact address - - muttguru@aol.com
Note for 2023..... Ken..."Less Stress - More Exercise!"
Ken
Always wanted - Details and pictures of M416 Trailer data plates & M151 data plates & body-tags for my research. Thanks!
Contact address - - muttguru@aol.com
Note for 2023..... Ken..."Less Stress - More Exercise!"
- svramselaar
- Major
- Posts: 1109
- Joined: December 30th, 2007, 6:48 am
- Location: holland
Re: Fuel tank drain plug needed
hi
i give it up
at my mutt there is a bolt with a ring
the parts number for the plug is MS20913-2S
at wb parts are two plugs ( see below) with different size`s
Ken has the right one
https://www.wbparts.com/search.cfm?q=ms+20913-2s
george
i give it up
at my mutt there is a bolt with a ring
the parts number for the plug is MS20913-2S
at wb parts are two plugs ( see below) with different size`s
Ken has the right one
https://www.wbparts.com/search.cfm?q=ms+20913-2s
george